|
Post by vangelis on Jul 2, 2014 11:40:24 GMT 1
Hi, Does anybody know why my LFOs do not function as soon as I release the keys. i mean that vibrato is heard as long as I hold a key(s) and stops when the envelope enters the release section....
Also I would like to know how I can loop an envelope(s) stage infinitely. I mean when the envelope reaches the sustain section, i want it to start over at the attack section.
Last, Is there any other autosleeper module except Scoofster autosleeper? I can't find this module anywhere.
Thank you.
Vangelis
|
|
|
Post by mindtraveller on Jul 2, 2014 14:07:28 GMT 1
Hi, there is a module by David Haupt called DH_EnvSeg. You can stack as many envelope segments as you like with this module. It's part of the DH_BasicModulePak. Dunno why your LFOs don't function during the release section. My LFOs do work and I haven't done anything special :-)
|
|
Claus
New Member
Posts: 62
Posts: 62
|
Post by Claus on Jul 2, 2014 20:53:56 GMT 1
Sounds like Your LFO is controlled by a GATE-signal somehow?
|
|
|
Post by vangelis on Jul 2, 2014 21:31:08 GMT 1
Well, I found my problem... I used an ADSR module on the LFO Depth in order to be able to delay the vibrato effect using the attack of the envelope (for Lfo delay time). I had attached a fader only on the attack pin, and I had set the decay and sustain to value=10 in the module's properties...but the release value was 7... I set it to 10 as well and now the vibrato stays until the end of the Amp Env.
As for DH_EnvSeg, it didn't serve my needs for some reason I can't remember...
Thank you for your time.
If there is some forum for beginners where I can post my questions now and then, please post a link.
Vangelis
|
|
|
Post by mindtraveller on Jul 2, 2014 23:17:30 GMT 1
Well, I'm also a beginner (have SE for about 10 months or so) but I'm somehow addicted to it :-)
|
|
Claus
New Member
Posts: 62
Posts: 62
|
Post by Claus on Jul 3, 2014 17:16:08 GMT 1
Well, I found my problem... I used an ADSR module on the LFO Depth in order to be able to delay the vibrato effect using the attack of the envelope (for Lfo delay time). I had attached a fader only on the attack pin, and I had set the decay and sustain to value=10 in the module's properties...but the release value was 7... I set it to 10 as well and now the vibrato stays until the end of the Amp Env. As for DH_EnvSeg, it didn't serve my needs for some reason I can't remember... Thank you for your time. If there is some forum for beginners where I can post my questions now and then, please post a link.Vangelis Yoa are already there, I think People make different kinds of plugins and thereby focuses on different aspects of SE. Ie. there are areas in SE I know very well, but in others I'm a total newb even though I started in around 2008. Best, Claus
|
|
|
Post by KlangManipulation on Jul 10, 2014 16:14:55 GMT 1
for a looping adsr you could use an internal-pattern-sequenzer.
|
|
|
Post by vangelis on Jul 11, 2014 19:38:03 GMT 1
As always, I didn't quite understand the sequencer thing. I cannot find an internal sequencer module.
|
|
|
Post by KlangManipulation on Jul 14, 2014 14:27:08 GMT 1
uhm.. yes there is no directly sequencer module, you have to build one. but there are more envelopes arround. for example CMR_8stageEnv1 or CK-Modules (but not freeware). for basicly sequenzing stuff you need a clock and a counter connected to a "many to one" switch.
EDIT: i was wrong and i corrected it now. i placed the CMR-module in the wrong folder. its not a KDL Module!
|
|
|
Post by vangelis on Jul 16, 2014 8:12:24 GMT 1
Thank you Klangmanipulation!
I have downloaded some KDL modules but this module can't be found on his site. Some links are broken. Where else can I download this module tha you mentioned?
vangelis
|
|
|
Post by KlangManipulation on Jul 16, 2014 17:57:04 GMT 1
mmm yes, i remember... they was downloadable at the old "SynthEdit Gathering" forum i think. i got this module and i could share them. but i dont know if its allowed! do you think it would be ok rob?
EDIT: i was wrong and i corrected it now. i placed the CMR-module in the wrong folder. its not a KDL Module!
|
|